Wie ich sehe funktioniert der Link nicht.
Also hier dann der komplette Inhalt:
Wie gesagt ab Step 3 liegt mein Problem
--------
So here are the command-line commands as I entered them, to create a working PXE boot with a valid BCD file. My instructions involve a technician computer running WinXP, which also serves as my TFTP server using tftpd32.exe. I also use VirtualPC on the technician computer to run WinPE 2.0 (see the previous article on how to create this VirtualPC). Step 1 and Step 2 correspond the the steps in the WAIK User's Guide article mentioned in the previous post.
Step 1 - Run these commands from the XP technician computer. My TFTP server is installed at c:\apps\tftpboot. Make sure you substitute the appropriate path for your environment.
Click Start, point to Programs, point to Windows AIK, and then click Windows PE Tools Command Prompt
Enter the following commands at the command prompt. Each bulleted item is a single command and should be typed on one line (even if it wraps to a new line in your web browser).
* copype x86 c:\winpe_x86
* imagex /mountrw c:\winpe_x86\winpe.wim 1 c:\winpe_x86\mount
Your command prompt should now have been changed to c:\winpe_x86
* md c:\apps\tftpboot\boot
* copy c:\winpe_x86\mount\Windows\Boot\PXE\*.* c:\Apps\tftpboot\boot
* copy "c:\Program Files\Windows AIK\Tools\PETools\x86\boot\boot.sdi" c:\apps\tftpboot\boot
* copy c:\winpe_x86\winpe.wim c:\Apps\tftpboot\boot
Step 2 - Run these commands from your Vista / WinPE 2.0 VirtualPC computer. After booting WinPE 2.0, you will automatically be presented with a command prompt. If runnning on Vista, open a command prompt.
* bcdedit -createstore c:\BCD
* bcdedit -store c:\BCD -create {ramdiskoptions} /d "Ramdisk options"
* bcdedit -store c:\BCD -set {ramdiskoptions} ramdisksdidevice boot
* bcdedit -store c:\BCD -set {ramdiskoptions} ramdisksdipath \boot\boot.sdi
* bcdedit -store c:\BCD -create /d "MyWinPE Boot Image" /application osloader
This last command will respond with a message like:
"The entry {02836f40-9ea0-11db-af23-0003ffc3f7f5} was successfully created."
The GUID WILL BE DIFFERENT FOR YOU. The GUID is the long series of numbers, letters, and dashes enclosed in braces {}. Do not copy the GUID used in my commands below. You must substitute the GUID returned by the previous command.
The following commands use MY GUID. Make sure you change it to yours.
* bcdedit -store c:\BCD -set {02836f40-9ea0-11db-af23-0003ffc3f7f5} systemroot \Windows
* bcdedit -store c:\BCD -set {02836f40-9ea0-11db-af23-0003ffc3f7f5} detecthal Yes
In the previous command, the setting is DETECTHAL in all lowercase. It is not DETECTHA1 - numeral one at the end.
* bcdedit -store c:\BCD -set {02836f40-9ea0-11db-af23-0003ffc3f7f5} winpe Yes
* bcdedit -store c:\BCD -set {02836f40-9ea0-11db-af23-0003ffc3f7f5} osdevice ramdisk=[boot]\Boot\WinPE.wim,{ramdiskoptions}
* bcdedit -store c:\BCD -set {02836f40-9ea0-11db-af23-0003ffc3f7f5} device ramdisk=[boot]\Boot\WinPE.wim,{ramdiskoptions}
* bcdedit -store c:\BCD -create {bootmgr} /d "Windows VISTA BootManager"
* bcdedit -store c:\BCD -set {bootmgr} timeout 30
* bcdedit -store c:\BCD -set {bootmgr} displayorder {02836f40-9ea0-11db-af23-0003ffc3f7f5}
Step 3 - Now I will copy the files created on my WinPE 2.0 VirtualPC to my TFTP server (my technician computer). These steps may be different, depending on your setup.
Run the following commands from the Vista/WinPE 2.0 computer. Substitute the values in ALL CAPS with values for your environment.
TFTPCOMPUTER is the name of your computer running the tftp server.
SHARE is the name of a shared folder on your tftp server.
VALIDUSER is the name of a user on the TFTPCOMPUTER that has write access to SHARE.
net use y:\\TFTPCOMPUTER\SHARE
when prompted for a username, I enter: TFTPCOMPUTER\VALIDUSER
When prompted for a password, I enter the password for VALIDUSER
When the command completes, I now have the Y: drive mapped to my server (technician computer). I run the following command from the WinPE 2.0 VirtualPC:
copy c:\BCD y:\tftpboot\boot
(My share maps to the parent folder - c:\apps - of my tftp server software, which is installed at c:\apps\tftpboot)
I then started tftpd32.exe from c:\apps\tftpboot on my technician/tftp server. I went to the "DHCP server" tab and changed the "Boot file" to: boot\pxeboot.com
I then started the tablet, hit F12, selected network boot, then pressed F12 again to confirm boot from the network. Windows PE booted on the tablet.
Hope this helps.
windows_pe.JPG
